Me7.4.5 Pinout

If an ECU is "bricked" due to a failed OBD flash, bench recovery is your only option.

The Bosch ME7.4.5 relies on a multi-plug configuration divided into distinct sub-segments (typically labeled as connectors ). It runs on an advanced STMicroelectronics C167 or ST10 series internal processor. This design manages complex functions such as drive-by-wire electronic throttle bodies, multiplexed CAN-bus operations, and variable radiator fan controls.

Individual injection triggers for cylinders 1-4.

For a standard bench connection (diagnostics and standard reading), the following pins on the

Understanding the is essential for automotive technicians, tuners, and DIY enthusiasts working on PSA Peugeot Citroën vehicles. This Engine Control Unit manages 16V petrol engines (such as the popular 1.6L NFU/TU5JP4). It coordinates everything from fuel injection and electronic throttle control to CAN-bus diagnostics and immobilizer security. me7.4.5 pinout

The immobilizer system in PSA vehicles is integrated with the ECU and the BSI. For IMMO-related tasks, such as performing an "IMMO off" procedure to bypass the immobilizer (often for engine swaps or when keys are lost), you will likely need to access the EEPROM chip. On the ME7.4.5, the relevant chip is an ST95320 (often labeled 95320) located inside the ECU on the back of the board. The process typically involves removing the ECU, desoldering this chip, and editing its binary file to disable the immobilizer before rewriting it. Alternatively, emulators can be used to override the IMMO system. The PIN code for the vehicle can also be extracted from the EEPROM dump.

| Pin | Signal | Description | |------|----------------|------------------------------| | 1 | Power | Permanent +12V (ECU main) | | 2 | Ground | Power ground | | 3 | Ignition output | Ignition coil cylinder 1 | | 4 | Ignition output | Ignition coil cylinder 2 | | 5 | Ignition output | Ignition coil cylinder 3 | | 6 | Ignition output | Ignition coil cylinder 4 | | 7 | Injector output | Injector cylinder 1 | | 8 | Injector output | Injector cylinder 2 | | 9 | Injector output | Injector cylinder 3 | | 10 | Injector output | Injector cylinder 4 | | 11 | O2 sensor heater | Pre-cat O2 heater (bank1) | | 12 | O2 sensor heater | Post-cat O2 heater | | 13 | MAF signal | Mass air flow sensor signal | | 14 | MAF ground | Sensor ground | | 15 | Sensor +5V | Reference voltage | | 16 | Throttle position | TPS signal | | 17 | MAP sensor | Manifold absolute pressure | | 18 | IAT sensor | Intake air temp | | 19 | ECT sensor | Engine coolant temp | | 20 | Knock sensor 1 | Signal | | 21 | Knock sensor 2 | Signal | | 22 | Cam position | Hall sensor signal | | 23 | Engine speed | Crank sensor signal | | 24 | CAN low | Diagnostic CAN bus | | 25 | CAN high | Diagnostic CAN bus | | 26 | K-line | Diagnostic K-line (ISO 9141) | | 27 | N75 valve | Boost control solenoid | | 28 | EVAP purge | Purge valve control | | 29 | SA output | Secondary air injection relay | | 30 | Fuel pump relay | Control signal | | 31 | Main relay | Power supply relay control | | 32 | Ground | Sensor ground | | 33 | +5V | Sensor supply | | 34 | TPS ground | Throttle position ground |

The ME7.4.5 manages vital engine functions including fuel injection, ignition timing, and emission controls. It typically features three main connectors—often referred to as Plugs A, B, and C—though the specific pinout for bench-mode operations (flashing/reading) generally focuses on a few critical pins in Plug C. Bench Connection Pinout

Viewed from the (wires entering, not the ECU pins): If an ECU is "bricked" due to a

The ME7.4.5 is almost always linked to a module via the CAN network. If the ECU is used in a different car, the EEPROM must be immo-offed or synchronized with the new BSI, or the car will not start.

The ME7.4.5 pinout is a critical piece of information for anyone working with the ME7.4.5 ECU. By understanding the pinout, technicians, engineers, and enthusiasts can ensure proper installation, configuration, and troubleshooting of the ECU and engine. Additionally, the pinout provides a foundation for custom modifications and tuning, allowing for optimized engine performance and efficiency. Whether you are a seasoned professional or a DIY enthusiast, familiarity with the ME7.4.5 pinout is essential for working with this sophisticated engine control unit.

Carefully break the factory silicone seal around the aluminum casing using a heat gun and pry tools. Be exceptionally careful not to slip and damage components on the edge of the circuit board.

| Pin | Connector | Signal Name | Description | Typical Function | |------|-----------|----------------|--------------------------------|--------------------------| | 1 | A | Ground | Sensor ground | - | | 2 | A | EVAP Canister Purge Valve (N80) | Duty cycle control | Emissions | | 3 | A | Ground | Power ground for injectors/coils | - | | 4 | A | +12V Battery | Permanent power (Terminal 30) | ECU memory | | 5 | A | +12V Switched (Terminal 15) | Switched via ignition | Wake-up signal | | 6 | A | CAN-High | Drivetrain CAN bus | ABS, Instrument cluster | | 7 | A | CAN-Low | Drivetrain CAN bus | ABS, Instrument cluster | | 8 | A | Brake light switch signal | Input | Brake pedal | | 9 | A | Clutch pedal switch | Input | Cruise control / starting | | 10 | A | A/C compressor request | Input | Climate control | | 11 | A | Radiator fan activation (low speed) | Output | Cooling | | 12 | A | Radiator fan activation (high speed) | Output | Cooling | | 13 | A | --- | Not used | - | | 14 | A | Alternator excitation signal | Output | Charge warning | | 15 | A | Diagnostic K-Line (ISO 9141) | Bi-directional | OBD2 communication | | 16 | A | --- | Not used | - | | 17 | A | --- | Not used | - | | 18 | A | --- | Not used | - | | 19 | A | Fuel pump relay control | Output | Activates FP relay | | 20 | A | Engine speed output (RPM signal) | Output | Tachometer cluster | | 21 | A | MIL (Check engine light) | Output | Warning lamp | | 22 | A | EPC light | Output | Electronic Power Control | | 23 | A | +5V Sensor supply | Reference voltage | For MAP, TPS, etc. | | 24 | A | --- | Not used | - | | 25 | A | --- | Not used | - | | 26 | A | --- | Not used | - | | 27 | A | --- | Not used | - | | 28 | B | Knock sensor 1 (cyl 1 & 2) | Signal input | Ignition timing control | | 29 | B | Knock sensor 2 (cyl 3 & 4) | Signal input | Ignition timing control | | 30 | B | Sensor ground (shield) | For knock sensors | - | | 31 | B | Intake Air Temp (IAT) | Signal input | Inside MAF or TMAP | | 32 | B | Engine Coolant Temp (ECT) | Signal input | Temperature compensation | | 33 | B | Shield ground | For crank/cam sensors | - | | 34 | B | MAF signal | Frequency/duty cycle | Airflow metering | | 35 | B | MAF ground | Sensor return | - | | 36 | B | G28 Engine speed (crank sensor) | Differential signal (-) | RPM base timing | | 37 | B | G28 Engine speed (crank sensor) | Differential signal (+) | RPM base timing | | 38 | B | G40 Camshaft position sensor | Hall effect signal | Sequential injection | | 39 | B | Throttle position sensor (G187) | Signal 1 (closing) | ETC | | 40 | B | Throttle position sensor (G188) | Signal 2 (opening) | ETC redundancy | | 41 | B | Accelerator pedal position (G79) | Signal 1 | Driver demand | | 42 | B | Accelerator pedal position (G185) | Signal 2 | Redundant signal | | 43 | B | MAP sensor (Integrated) | Boost pressure signal | Inside ECU case | | 44 | B | MAP sensor ground | Internal ECU | - | | 45 | B | External MAP (for some models) | Boost input (rare) | - | | 46 | B | --- | Not used | - | | 47 | C | Injector cylinder 1 | Output (ground switch) | Fuel delivery | | 48 | C | Injector cylinder 2 | Output (ground switch) | Fuel delivery | | 49 | C | Injector cylinder 3 | Output (ground switch) | Fuel delivery | | 50 | C | Injector cylinder 4 | Output (ground switch) | Fuel delivery | | 51 | C | Ignition coil 1 (power stage) | Output | Spark | | 52 | C | Ignition coil 2 (power stage) | Output | Spark | | 53 | C | Ignition coil 3 (power stage) | Output | Spark | | 54 | C | Ignition coil 4 (power stage) | Output | Spark | | 55 | C | N75 Boost control valve | PWM output | Wastegate control | | 56 | C | Idle Air Control (N71) | PWM output (if not DBW) | Idle stabilization | | 57 | C | Secondary air injection pump relay | Output | Cold start emissions | | 58 | C | Secondary air injection valve (N112) | Output | Air diverter | | 59 | C | O2 sensor heater (Bank 1, Sensor 1) | Output | Lambda heating | | 60 | C | O2 sensor heater (Bank 1, Sensor 2) | Output (post-cat) | Heating | | 61 | C | O2 sensor (Sensor 1) signal | Input (0-1V or wideband) | AFR | | 62 | C | O2 sensor (Sensor 1) ground | Ground for lambda | - | | 63 | C | O2 sensor (Sensor 2) signal | Input | Post-cat monitoring | | 64 | C | O2 sensor (Sensor 2) ground | Ground | - | | 65 | C | Fuel tank pressure sensor | Input | Leak detection | | 66 | C | --- | Not used | - | | 67 | C | --- | Not used | - | | 68 | C | --- | Not used | - | | 69 | A | +12V Switched (Terminal 15) duplicate | Redundant | Safety | | 70 | A | Ground | Power ground | High current | | 71 | A | Ground | Power ground | High current | | 72 | A | +12V Battery duplicate | Redundant main power | - | | 73 | A | +12V Battery duplicate | Redundant main power | - | | 74-121 | --- | Various unused or vehicle-specific pins | (e.g., cruise control, A/C pressure) | Check wiring diagram | This design manages complex functions such as drive-by-wire

This guide covers the 80+ pins across the three connectors (, T60a , T60b ), focusing on the essential signals for diagnostics, tuning, and swap wiring.

In instances where the original ECU data is completely lost, a software patch can be applied to the donor EEPROM file to permanently disable the immobilizer request. Keep in mind that a permanent Immo Off on Bosch ME7.4.5 sometimes results in a persistent cooling fan fault or an error message on the dashboard screen depending on the specific firmware version used. Best Practices and Safety Tips

You can log AFR by tapping the wideband’s 0-5V analog output into an unused . Common choices: